Top ten problems and solutions that are easy to appear during the use of the engraving machine

Question 1: When opening the software, the computer prompts "Failed to open the card, please check the card".
Solution:
1. Check if the driver of the board is installed or replace the card with a PCI slot;
2. Reinstall the two data cables to check for broken needles.
3. Weihong card has a problem, replace the card.
Question 2: Prompt when opening the software: three-axis alarm, initialization error signal.
Solution:
1. Check if the two data cables of the computer and the machine are connected;
2. Check if the fuse of the adapter plate in the control box is burned out and replace the fuse;
3. Check if the power supply is normal.
Question 3: Misalignment occurs during engraving, or the size is wrong.
Solution:
1. Check if the path of the engraving software is correct or not;
2. Check the gap size of the screw and the loosening of the fastening screw of the polished rod;
3. Check if the software parameters are set correctly.
Question 4: When the X-axis is walking a certain section, the Z-axis does not raise the knife. Press it up and go down.
Solution:
1. Check if the Z-axis motor is running normally, the power and the current of the driver;
2. Check if the Z-axis motor line has poor contact or intermediate disconnection.
3. Check if the lift distance is set.
Question 5: The spindle motor does not rotate or reverse.
Solution:
1. Check the settings of the parameters of the inverter;
2. Whether the signal line of the inverter is reversed.
Question 6: A sickle phenomenon occurs.
Solution:
1. The Z-axis motor has insufficient power and the coupling is loose;
2. The current of the Z-axis driver is too small, or the signal line is wrong.
3. The data line is not connected.
Question 7: When the software is turned on, the axis turns off.
Solution:
1. The problem of the drive or the poor connection of the computer output signal line;
2. Poor motor line contact.
Question 8: The machine is not powered when it is turned on.
Solution:
1. Check if the start button wire is connected and the button is burnt out;
2. Check if the AC contactor is shorted or burned out.
Question 9: The axis only goes in one direction when the button is moving.
Solution:
1. Check if the data cable is normal and the data cable socket is plugged in.
2. Check if there is any solder joint on the motor circuit.
Question 10: The sending software can't open normally, and the engraving stuff is deformed.
Solution:
1. Reinstall the new system and software;
2. Check if the X, Y axis screw and screw are loose;
3. There is a problem with the carving path

What kind of configuration should be equipped with high-grade sliding door woodworking engraving machine?

The sliding door engraving machine is the highest configuration machine in the ordinary engraving machine. Nowadays, the sliding door engraving machine produced by many manufacturers in Jinan is modified by woodworking engraving machine. Many accessories can not keep up with the overall needs of the machine, so it will lead to the engraving machine in the operation process. There are minor problems in the medium frequency. In order to meet the needs of the market, Jinan Snow Scientific has developed a sliding door engraving machine for professional production. Xiaobian introduces the obvious advantages of the sliding door engraving machine.
Firstly, the sliding door engraving machine generally adopts double-head configuration. The double-head sliding door engraving machine can improve the engraving efficiency of the sliding door panel. The sliding door engraving is deep relief carving, and the single-head engraving speed is slow, so it is necessary to adopt a double-head design, so that it can be greatly Increased production efficiency.
Double-head engraving needs to increase the width of the machine. Our company will widen the machine to 1.8 meters, ensuring that two coffin plates can be engraved at the same time. The machine bed is made of thick square tube (usually 5mm thick steel plate, If the customer has special requirements, it can be thickened), which fully guarantees the stability of the machine.
Once again, the machine uses 8MM thick seamless welded steel gantry to ensure that the gantry does not shake and deform under high-intensity working conditions.
The selection of accessories is also the selection of the best domestic accessories. Changzhou Hanqi's high-power water-cooled spindle, the Japanese extension brand inverter, the guide rails are all genuine Taiwan's silver square track, to ensure the overall operation of the machine is stable.
The use of sliding door engraving machine began in the past few years, but the technology has matured in the past two years. Jinan Ludiao CNC has developed a professional sliding door engraving machine for the needs of the market, allowing customers to use the most suitable machine. The most suitable job.